Photo Gallery: Omicron Models and Installations

Below we show many of our commonly specified solutions for New York City applications, ordered as follows:  Starting with our simplex filter for a typical lead-lag-standby house pump design, we work our way down through lower max flow rates.  Then we show duplex solutions for larger flow rates and/or redundancy.  At the end of the gallery we show a typical storm water solution, integrating filtration + ultraviolet light disinfection, with circulation pump and pressure sustaining valve included on the skid.

Note about max flow rates stated:  These are not meant as strict upper limits, but rather as conservative max values based on our many years of experience with New York City's highly turbid water conditions.  The default micron rating for these limits is 10 micron unless noted otherwise.  Max flow rates are higher when using a coarser screen (e.g. 25 micron) and also should be higher in most cities outside of New York.

 

All models are available in high pressure versions to enable installation downstream of house pumps:  "PN16" for up to 230 psi, or "PN25" up to 360 psi.

Our most often specified Omicron 21300-10(H) 316L21300 references screen area (cm2), -10 micron, (H) horizontal orientation, 316L stainless.  A complete skidded system, including flush line pump to boost pressure during backwash cycles.  Max flow @ 10 micron:  350 gpm.  Drawing  


 

Side view of Omicron 21300-10(H) 316L  Drawing


The same model except built for medium high pressure, our PN16 version for up to 230 psi:  Omicron 21300-10(H) PN16 316L.  Note the flush pump is deleted from the skid:  With high pressure systems there is no need to boost pressure during backwash cycles.  Drawing


Omicron 10600-10(H) 316L for a max flow rate @ 10 micron of 165 gpm.  Space was tight, so the filter was ordered without the factory-built frame and assembled on site.  The panel can be seen in the distance, wall-mounted.   A simple bucket is here used to detain the discharge from flush cycles to drain.  Drawing

                 Omicron 5300-10(V) 316L for flow rates @ 10 micron up to 60 gpmor 5300-25(V) 316L @ 25 micron up to 100 gpm).  This model is especially suitable for retrofits as it can be moved into place through limited access halls and doorways. 

The unit can also be manifolded (e.g. x2 or x3) for higher flow rates, with manifold piping supplied as a separate. 

Drawing 5300-10(V)

Drawing 5300-25(V)

Drawing Triple 5300-10(V) 

See more configuration drawings of the 5300 series

 

Omicron 2650-25(V) in coated carbon steel, installed for a seven-unit condo with a flow rate of max 30 gpm. 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Twin manifolds are commonly ordered for two principal reasons:
(1) to accommodate a higher flow rate, (2) for redundancy, partial or full. 


Omicron Twin 13200-10(H), here ordered in coated carbon steel, is designed for up to 440 gpm.  Drawing


Omicron Twin 16500-10(H) 316L for up to 550 gpm, configured side by side.  A single flush pump serves both filters as they never backwash together.  Drawing


A more space-efficient design of Omicron Twin 16500-10(H) 316L, a stacked configuration, reduces required footprint.  Drawing


Omicron Twin 21300-10(H) 316L for flow rates @ 10 micron up to 700 gpm (and/or redundancy depending on the max flow expected).  This duplex system is only available in a side-by-side configuration.  Drawing


Another view of Omicron Twin 21300-10(H) 316L after installation.  Drawing


The 21300 series is here seen in a vertical orientation, Omicron Twin 21300-10(V) 316L also for up to 700 gpm.  The vertical orientation reduces footprint but requires adequate ceiling height to accommodate the davit that supports the covers when rotated and lifted above the filter housings.  Drawing


At this building with two separate points of entry that converged in the center, the single 21300 for the lower flow rate was mounted above the twin 21300 for the higher flow.  A platform is required to enable periodic maintenance of the upper filter.  (Don't try this at home!)


Detail of a twin stacked manifold.  The filters are separated by just inches to reduce required height as much as possible.


The perfect storm water system, Omicron 2900UV-50-CP.  The UV is factory-integrated downstream of the filter in a consolidated footprint.  Circulating pump and pressure sustaining valve are included on the skid.  Water flows from bottom to top.  The skid is located next to the storm water retention tank and assures a circulating flow in and out of the tank.  Drawing


A close up view of the 2900UV-50.  All 316L stainless.  Available also with 25 micron screens and in twin-parallel skids for higher flow rates.